Polyethylene PE1000 Rod - UHMWPE
Uhmw Pe 1000 Rod:
PE Rod ha e na monko, ha e chefo, e ikutloa joaloka boka, e na le mocheso o motle o tlaase (mocheso o tlaase ka ho fetisisa o ka fihla ho 70 ~ 100 °C), botsitso ba lik'hemik'hale bo botle, boholo ba khoholeho ea asiti le alkali (acid) e nang le litšobotsi tsa ho hanyetsa oxidation. Thempereichara ha e qhibilihe ka har'a lihlapolli, metsi a manyenyane, thepa e babatsehang ea ho kenya motlakase; Boima bo tlaase; boima bo botle, bo sebetsa le maemong a mocheso o tlaase); Ho otlolla hantle; Insulation ea motlakase le dielectric; Sekhahla se seholo se tlase; Mouoane oa metsi tlase;Botsitso bo botle ba lik'hemik'hale;Non-chefo e se nang kotsi.
Empa PE Rod bakeng sa khatello ea tikoloho (lik'hemik'hale le phello ea mechine) e na le kutloelo-bohloko haholo, ho tsofala ha mocheso.
Likarolo tsa lisebelisoa tsa bongaka, litiiso, liboto tse sehang, liprofaele tse thellang.E sebelisoa haholo indastering ea lik'hemik'hale, mechine, indasteri ea lik'hemik'hale, matla a motlakase, liaparo, liphutheloana, lijo le liindasteri tse ling. E sebelisoa haholo phetisong ea khase, phepelo ea metsi, metsi, ho nosetsa, merafong likaroloana tse ntle tsa phepelo e tiileng, le tšimo ea oli, indasteri ea lik'hemik'hale le mehala ea puisano le mafapha a mang, haholo-holo phepelong ea khase e sebelisitsoe haholo.
Melemo ea molamu oa uhmwpe:
1. Matla a matle a Tensile
2. Tšusumetso e phahameng le matla a khahlanong le tšusumetso
3. Mocheso o phahameng oa ho kheloha mocheso
4. Matla a phahameng le boima
5. Libapali tse ntle tsa glide le tse bonolo tsa lapeng
6. Botsitso bo botle ba lik'hemik'hale khahlanong le li-solvents le mafura
7. E hanana le botsofali ba mocheso (mocheso o sebetsang o pakeng tsa -60°C le 190°C
8. Phetoho ea boholo ka ho monya mongobo e tlameha ho nahanoa
Likarolo tsa ts'ebeliso ea ROD ea uhmwpe:
Liaparo, likarolo tsa phetisetso, likarolo tsa lisebelisoa tsa lapeng, likarolo tsa koloi, molamu oa terata ho thibela likarolo tsa mochini, likarolo tsa mochini oa lik'hemik'hale, lisebelisoa tsa lik'hemik'hale, joalo ka turbine, gear,bearing, impeller, shaft, dashboard, shaft drive, valve, blades, terata. , li-washer tse nang le khatello e phahameng, li-screw, linate, li-seal, li-shuttle bushing, sehokelo, joalo-joalo.
Boholo ba melamu
| Mmala | Bolelele ba Molamu (mm) | Thupa Diameter (mm) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 20 | 25 | 30 | 35 | 40 | 50 | 60 | 65 | 70 | 80 | 90 | 100 |
| Tlhaho | 2000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Tlhaho | 1000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Ntsho | 2000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Ntsho | 1000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Botala | 2000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Botala | 1000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Boputsoa | 2000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Boputsoa | 1000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Mmala | Bolelele ba Molamu (mm) | Thupa Diameter (mm) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 110 | 120 | 130 | 140 | 150 | 160 | 180 | 200 | 230 | 250 | 300 |
| Tlhaho | 2000 | * | * | * | * | * | * | * | * | * | - | - |
| Tlhaho | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Ntsho | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Ntsho | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Botala | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Botala | 1000 | * | * | * | * | * | * | * | * | - | - | - |
| Boputsoa | 2000 | - | * | - | - | - | - | - | - | - | - | - |
| Boputsoa | 1000 | - | * | - | - | * | - | - | - | - | - | - |
Litlhaloso tsa UHMW-PE ha li bapisoa le Plastiki e 'ngoe ea Boenjiniere
| Ntho | Unint | UHMW-PE | ABS | PA-66 | POM | PTFE |
| Botenya | g/cm^3 | 0.935 | 1.03 | 1.41 | 1.41 | 2.14-2.30 |
| Flash point | ºC | 136 | 165 | 25 | 165 | 327 |
| Ntlha ea Khohlano | -- | 0.1-0.22 | -- | 0.15-0.40 | 0.15-0,35 | 0.04-0.25 |
| Sekhahla sa ho Monyeha ha Metsi | % | <0.01 | 0.20-0.45 | 1.5 | 0.25 | <0.02 |
| Matla a tšepe | MPa | ≥38 | 22-28 | ≥80 | 62-70 | 15-35 |
| Elongation at Break | % | ≥300 | ≥53 | ≥60 | ≥40 | 200-400 |
| Matla a Tšusumetso | KJ/m^2 | 70 | ≥22 | 4.5 | -- | -- |
| Ho hanyetsa Molumo | Ω.cm | 10^17 | 10^15 | 5*10^14 | 10^14 | >10^17 |
| Monyetla oa ho Aroha | KV/mm | 50 | 15 | 15 | 20 | 20 |
| Dielectric Constant | 10^6HZ | 2.2 | 2.4 | 3.7 | 3.7-3.8 | 1.8-2.2 |
| Dielectric Loss Tangent | 10^6HZ | ≤5*10^-4 | 4*10^-2 | 2*10^-2 | 5*10^-2 | ≤2.5*10^-4 |
Melemo ea rona:
A: Mofani oa lihlahisoa tsa uhmwpe ea nang le boiphihlelo
B: Sehlopha sa meralo ea litsebi le lefapha la thekiso bakeng sa ts'ebeletso ea hau
C: Re ka fana ka sampole e nyane ea mahala kapa ra fumana odara ea sampole e nyane.
D: Tšebeletso ea 8/24 bakeng sa hau, lipotso tsohle li tla sebetsanoa nakong ea lihora tse 24
E: Boleng bo tsitsitseng---- bo tsoang ho thepa e ntle le theknoloji
F: Theko e tlaase----ha e theko e tlaase empa e tlaase ka ho fetisisa ka boleng bo tšoanang
G: Ts'ebeletso e ntle----tšebeletso e khotsofatsang pele le ka mor'a thekiso
H: Nako ea thomello----15-20 matsatsi a tlhahiso ea bongata
